WILDSTAR Gen2 RTM for 6U OpenVPX – WP6R20
RTMs facilitate high-speed and general-purpose I/O transfers between WILDSTAR™ 6U OpenVPX motherboards and other components.
This Rear Transition Module is compatible with WILDSTAR UltraK and WILDSTAR A10 6U OpenVPX motherboards.

General Features
- Supports Xilinx-based WILDSTAR UltraScale for OpenVPX and Intel-based WILDSTAR Arria 10 for OpenVPX cards
Rear Panel I/O
- Two QSFP+ with CDR for enhanced signal integrity for FPGA HSS
- CPU I/O Support (availability depends on payload card type/configuration)
- One SFP+ with CDR for enhanced signal integrity
- RJ45 Ethernet Port
- USB 3.0 Host with USB Type C connector
- Supports USB 2.0 and 3.0 connections
- USB UART Serial Port Console
- Micro-DB9 for RS-232, RS422 or RS-485 support
- SMA supporting IRIG-B input, clock output, or clock input. Can be AC or DC coupled and supports TTL and LVPECL levels as well as software selectable termination and threshold settings.
- Can support 1 PPS input or output
- Dual CHAMP connectors for LVDS and Single ended IOs
- High Speed LVDS buffers for additional ESD protection
- Supports twenty-four 5V or 3.3V (switch selectable) Single Ended IO on each CHAMP connector (controlled via I2C from payload CPU)
- Supports up to 16 LVDS and four 2.5V single ended FPGA connections per CHAMP connector
- CHAMP LVDS is uni-directional and can be ordered as all TX, all RX or a combination of TX/RX
System Management
- Hot Swappable
Mechanical and Environmental
- 6U OpenVPX (VITA 65) Compliant
- Available in Industrial Temperature Grades
Application Development
- JTAG FPGA debug connector for Xilinx Chipscope or Intel SignalTap debug cables
The following documentation is available for registered users of our site. Please log in or feel free to register for our site.
Technical Documents
For additional documentation, please contact your Sales Representative.
Related Products
WILDSTAR A10 2PE for 6U OpenVPX – WB6A12
WILDSTAR™ A10 2PE for 6U OpenVPX boards include two Intel Arria 10® GX900, GX1150, GT1150 FPGAs with High Speed Serial connections performing up to 15 Gbps. There is also an on-board dual ARM Cortex-A9 Processor running up to 925 MHz which can be used for local application requirements without using PCIe bandwidth.
WILDSTAR A10 3PE for 6U OpenVPX – WB6A13
WILDSTAR™ A10 3PE for 6U OpenVPX boards include three Intel Arria 10® GX900, GX1150, GT1150 FPGAs with High Speed Serial connections performing up to 15 Gbps. There is also an on-board dual ARM Cortex-A9 Processor running up to 925 MHz which can be used for local application requirements without using PCIe bandwidth.
WILDSTAR UltraKVP 2PE for 6U OpenVPX – WB6XU2
WILDSTAR™ UltraKVP 2PE for 6U OpenVPX boards include one or two Xilinx® Kintex® UltraScale™ XCKU115 or Virtex® UltraScale+™ XCVU5P/XCVU9P FPGAs with High Speed Serial connections performing up to 16.3 Gbps. There is also an on-board dual ARM Cortex-A9 Processor running up to 766 MHz which can be used for local application requirements without using PCIe bandwidth.
Private: WILDSTAR UltraKVP 3PE for 6U OpenVPX – WB6XU3
WILDSTAR™ UltraKVP 3PE for 6U OpenVPX boards include three Xilinx® Kintex® UltraScale™ XCKU115, Virtex® UltraScale™ XCVU125/XCVU190 or Virtex® UltraScale+™ XCVU5P/XCVU9P FPGAs with High Speed Serial connections performing up to 16.3 Gbps. There is also an on-board dual ARM Cortex-A9 Processor running up to 766 MHz which can be used for local application requirements without using PCIe bandwidth.